Directed Electronics S 580 E Uživatelská příručka stáhnout pdf (Strana 30)

Domů
Directed Electronics
Vzdálené spouštěče
S 580 E
Uživatelská příručka

Stažení
Sdílet

Sdílení
Přidat do mých příruček
Tisk

24 Operation

3.7 Safe Z-Height

Safe Z-height is determined by choosing a height that ensures the needle, height sensor, or any part of

the dispensing head does not collide with any obstacles while traveling around the dispensing area.

3.7.1 Setting Safe Z-Height

Safe Z-height is the height below which the tip of dispensing head cannot go when moving from one set

of coordinates to another during operation.

To set the Safe Z-Height:

1. In the FmXP Main Window, click on Run a Program.

 The Production Window opens.

2. In the Production Window, click on the Setup button (Figure 3-4).

Figure 3-4 Production Window

3. Click on Teach Safe Z-Height.

 The Teach Safe Z-Height Window shown in Figure 3-5 opens.

1 2 ... 25 26 27 28 29 30 31 32 33 34 35 ... 63 64

DispenseMate 1
Dispensing System 1
Manuals on the Internet 2
Contact Us 2
Trademarks 2
Table of Contents 3
Table of Contents iii 5
1 Introduction 7
1.2 Safety First 8
1.3 Getting Started 8
1.4 Standard Equipment 9
1.5 Optional Equipment 9
1.6 Dispensing Valves 10
1.7 Front View Features 11
6 Introduction 12
Height Sensor 13
1.7.1 Dispensing Area 13
Vision System 13
Dispensing Valve 13
Tooling Plate 13
1.8 Rear View Features 14
Introduction 9 15
2 Safety 16
2.4.1 Safety of Personnel 17
2.4.2 Material Safety 18
Safety 13 19
2.6 Safety Warning Labels 20
Safety 15 21
2.7 Emergency Shutdown 22
Safety 17 23
2.9 Interlock 24
3 Operation 25
3.5 Startup 26
3.6.1 Using the Touchpad 27
22 Operation 28
3.6.2 Using the Keyboard 29
3.7 Safe Z-Height 30
Operation 25 31
3.8 Adjusting the Camera 32
Operation 27 33
(in unlinked mode) 33
To calibrate the camera: 34
3.8.3 Focusing the Camera 35
30 Operation 36
3.10 Adjusting Air Pressure 37
32 Operation 38
Operation 33 39
3.11 Setting the Heaters 40
Operation 35 41
To start a production run: 42
Operation 37 43
3.13 System Shutdown 44
4 Maintenance 45
40 Maintenance 46
To replace the purge boot: 47
4.5 Draining the Water Trap 48
To remove the axis covers: 49
To lubricate the cables: 49
44 Maintenance 50
4.8 Tensioning the Cables 51
46 Maintenance 52
5 Troubleshooting 53
5.4.1 System Power 54
5.4.2 Pneumatic 54
Master Offsets in FmXP 55
5.4.5 Vision System 56
6 Specifications 57
6.4.1 DispenseMate 583 58
6.4.2 DispenseMate 585 58
6.4.3 Software 58
Appendix A Block Diagrams 59
Appendix B Parts List 60
B.4 Illustrated Parts List 61

Komentáře k této Příručce

Žádné komentáře

Directed Electronics S 580 E Uživatelská příručka Strana 30

Komentáře k této Příručce

Související produkty a manuály pro Vzdálené spouštěče Directed Electronics S 580 E